Adventures In Audio
Loudspeakers: Know your continuous from your program from your peak

David Mellor

David Mellor is CEO and Course Director of Audio Masterclass. David has designed courses in audio education and training since 1986 and is the publisher and principal writer of Adventures In Audio.

Thursday March 17, 2011
FREE EBOOK DOWNLOAD ►

The power rating of a loudspeaker might be 500 watts; it might be 2000 watts. But how much power can it truly handle?

The power rating of a loudspeaker might be 500 watts; it might be 2000 watts. But how much power can it truly handle?

Here is an interesting question from an Audio Masterclass student:

I saw something at the back of a Wharfedale PRO EVP-X215 loudspeaker that I don't understand what it means. This is it...

  • 500 watts continuous
  • 1000 watts program
  • 2000 watts peak

I just want to know what it means.

OK, so we have one loudspeaker with three different power ratings. How does that work?

Well the first thing you have to understand is that loudspeaker manufacturers guess the power ratings of their products. Yes they guess the ratings. Well, they make an informed guess based on testing and a knowledge of their market. But specifying how much power a loudspeaker can take is a lot more difficult than measuring how much power an amplifier can produce.

The first thing to understand is what we mean by power rating. In the most useful sense, it is the amount of power a loudspeaker can handle without blowing. Give it anything up to that amount of power, and it will stay healthy, ready for the next session or gig. Overstep that mark and you have a speaker that rattles or has a drive unit that doesn't work at all.

The ultimate test of any loudspeaker is in the hands of a real-life user. Does the speaker fulfill the user's expectations without blowing? Or does it blow? If the user considers that the speaker has blown prematurely, then they won't buy that model (or from that manufacturer) again.

So the manufacturer has to strike a balance between quoting a high figure that will impress a potential purchaser, and a realistic figure that won't result in too many blowages.

But why three ratings? What does that mean?

The first rating, 'continuous', is where the same amount of power is applied continuously and without respite. It is the most conservative rating and represents a 'worst case' scenario. This is assessed using a test bench signal; in the real world you would get closest to this by playing an Oasis CD that has been mastered to within an inch of its life.

A continuous signal pumps more and more energy into the loudspeaker, most of which turns to heat. Apply too much power for too long and the temperature will rise to a point where the voice coil of one of the drivers literally melts.

The second rating, 'program', represents a more realistic scenario where the input level rises and falls, thus giving the speaker time to rest and disperse some of its waste heat.

The third, 'peak', is the highest momentary level that the speaker can be expected to withstand. Applying levels this high not only implies a lot of heat generation, albeit for short time periods, but also very rapid and extreme movements of the diaphragm of the drive unit. What can happen here is that the turns of the voice coil deform and perhaps separate. So although the drive unit still works, it rattles as the coil scrapes against the magnet.

There are defined specifications by which a manufacturer can make all of these measurements in a controlled and meaningful way. In the end though, it is the responsibility of the person behind the faders to listen to the sound quality being produced, and have a knowledge of how much their speakers can take.

P.S. I was once tasked with assessing how much level I could get out of a speaker on a sound effect at a certain point in a theatre show, without it blowing. I was able to do the test in the auditorium (while the lighting and stage crews were on a break!). After around six or seven blown drive units, I felt I had a pretty good idea!

Like, follow, and comment on this article at Facebook, Twitter, Reddit, Instagram or the social network of your choice.

Come on the Audio Masterclass Pro Home Studio MiniCourse - 60 great hints and tips to get your home recording studio MOVING

It's FREE!

Get It Now >>

How to choose the best key for your song

What is comb filtering? What does it sound like?

NEW: Audio crossfades come to Final Cut Pro X 10.4.9!

What is the difference between EQ and filters? *With Audio*

What difference will a preamp make to your recording?

Watch our video on linear phase filters and frequency response with the FabFilter Pro Q 2

Read our post on linear phase filters and frequency response with the Fabfilter Pro Q 2

Harmonic distortion with the Soundtoys Decapitator

What's the best height for studio monitors? Answer - Not too low!

What is the Red Book standard? Do I need to use it? Why?

Will floating point change the way we record?

Mixing: What is the 'Pedalboard Exception'?

The difference between mic level and line level

The problem with parallel compression that you didn't know you had. What it sounds like and how to fix it.

Compressing a snare drum to even out the level

What does parallel compression on vocals sound like?

How to automate tracks that have parallel compression

Why mono is better than stereo for recording vocals and dialogue

Clipping and compressing a drum recording to achieve an exciting sound texture

What can we learn about room acoustics from this image?

Can you hear the subtle effect of the knee control of the compressor? (With audio and video demonstrations)

What is the best studio microphone?

What is the Neve sound? (Using the Slate Digital FG-73)

What is the difference between recording, mixing and mastering?